What Are the Benefits of a Mosfet on an Airsoft Rifle

The pros and cons of using additional electronics in your AEG replica is the topic of very long give-and-take. Both the supporters and the opposition of electronics take their good points, that make them to not utilise any alternative. However, there are also people who utilise both stock guns and electronic units, dependind on the situation. I am one of them, so I can tell y'all most both the advantages and the disadvantages of those solutions.

To be specific, past saying "electronics" I mean all kinds of electronic units like MOSFETs, programmable units and even thing similar GATE Titan for ASCU.

Electronic units in my airsoft replicas

Currently I have four guns, two of them take electronics inside

a P90 replica from the Cyma brand lying on a paving stone

In my CYMA P90 I take a standard type MOSFET (the review of this model tin be found here).

ELAR SOPMOD replica lying on a paving stone

In my lovely ELAR SOPMOD 2 I have the GATE TITAN unit (see my mail virtually it).

E&L replica in camouflage pattern on cobblestones

In my 2d East&L M4 I oasis't done any changes in the stock wiring as well the connector blazon.

a&k m249 replica in black lying on cobblestones

In my A&K M249 I have simply replaced the wiring.

Electronic units in the AEGs - advantages

At that place are a few basic pros of using electronic units in your gun, even the simplest MOSFET models. The most important one is the amend trigger response, which allows 1 to shoot faster on the semi mode.

airsoft replica interior, trigger, gears and piston titan type mosfet from the gate brand

The other advantage is the fact, that MOSFET unit prevents the switch from burning when using high voltage batteries. This trouble is noticeable in airsoft replicas that are used with 11,1 V batteries and accept already shot a lot of bbs. When there is a lack of whatsoever trigger response - it's probably considering the switch is burned and needs a replacement. With the MOSFET installed, this trouble never appears.

If you're using a more powerful AEG motor and 11,1 V bombardment, I would recommend to installing the MOSFET with Agile Breaking Arrangement, that prevents the gears from overspin in ane shot bike. This problem can announced with high-speed gears or weaker springs.

titan gate mosfet unit

The real fun begins, when the MOSFET is programmable. The simplest models allow a user to command the battery cells voltage or setting the burst fashion. The well-nigh premium units are fully programmable with a special card, USB cable or even Blueetoth Android connexion.

Electronic units in the AEGs - disadvantages

The easiest style to explain information technology is the fact that the electronics are just another delicate part of an airsoft replica that can be broken.

The most common outcome is the curt circuit, which is usually caused by improper apply of the device or bad mounting. The symptom is obvious - replica constantly shoots full auto. In case of highly upgraded gearboxes, especially with powerful springs, information technology can stop up with everything destroyed within. It can exist stopped just by disconnecting the bombardment.

Talking most the proper using and mounting - the MOSFETs aren't projected with rainy conditions in mind. Yep, most of them are perfectly sealed, but as Forrest Gump said - information technology happens. In farthermost rain atmospheric condition, I would definitely recommend leaving the MOSFET upgraded replica at home.

man in uniform with gloves and airsoft replica

All the same, if the rain is not that heavy and we want to go out for a skirmish - it's skillful to recollect some safety precautions. Never point the MOSFET unit downward, considering the h2o will drain off through the barrel to the electronics. After the game - disconnect the bombardment and dry out off the replica. If you keep the battery in stock - seal all holes with the electric tape. Fun fact - I personally know someone who left a wet gun with the MOSFET and the connected battery... with the barrel pointed to the sky. Water has found its manner to the MOSFET, which concluded in a furious full auto session with burned electronic unit and cleaved AEG motor.

However in my TITAN, fifty-fifty with its waterproofness, the unit can get crazy because of a single drop of h2o. It's due to the optical sensors in the trigger unit and fire selector,

As you lot tin see, everything has its advantages and disadvantages in unlike situations. This gives you an excuse to add another gun to your collection ;)

Author:

Paweł "Fishbonee" Napieralski

Did you similar our article? Read more texts past this author - you can notice themHither!